Flat price
Quoted before we drain the old tank
When your water heater quits, you need water heater installation Spring TX homeowners call because we show up, pull the old tank, and have hot water running the same day. We install Rheem, Bradford White, Navien, and AO Smith units sized for your home, handle the permit, and haul the old heater away. One call gets it done.
Every install includes the new unit, the permit, the fittings, the drain pan, the expansion tank, and the haul-away. We do not charge extra for a new T&P valve or a longer gas connector. If we find a corroded shutoff valve or a bad vent, we quote it before we fix it.


We replace failed and aging water heaters in Spring homes, from a 40 gallon garage tank to a wall-mounted tankless unit. You get a flat price, a permitted install, and a walkthrough before we leave.
We install commercial water heaters for property managers, restaurants, and small offices in Spring. We work around your hours and pull the permit so the job passes inspection.
Water heater installation Spring TX is the full removal and replacement of your failed or aging water heater, including the tank, fittings, venting, expansion tank, drain pan, and code-required safety components. We drain the old unit, cut out corroded nipples, inspect the shutoff valve, and set the new heater on a level pad. Gas units get a new flexible connector and sediment trap; electric units get new elements and a properly sized breaker check. Every install ends with a leak test, a temperature check at the tap, and a walkthrough of the anode rod schedule.
Most Spring homes we service were built between 1975 and 2005, and the original water heaters in those houses are long past their 10 to local experience life. If you are searching for water heater installation Spring TX near me because your tank is leaking onto the garage floor, we treat it as urgent. We also handle planned water heater replacement Spring Texas jobs when you want to upgrade to a larger tank or switch to tankless before the old unit fails.
We drain the old tank, install the new one to code, and stay until the hot water runs.
From the first call to the final walkthrough, here is exactly what happens when we install your new water heater in Spring.

Used to disconnect the old water lines and cut copper or PEX pipe to size. A clean cut means a proper fit and no leaks at the connection.

For soldering copper joints or pressing fittings on PEX and copper lines. We use the press tool when a flame is not safe near framing or insulation.

Our trucks carry RIDGID pipe wrenches and Milwaukee cordless tools for cutting, drilling, and tightening. These brands hold up to daily use and let us work faster on tight installs.

We use electronic leak detection equipment to check for hidden leaks in the lines before we connect the new heater. Finding a slab leak now saves you a flooded floor later.

For quick, reliable connections on PEX and copper where a press or solder joint is not practical. SharkBite fittings are code-approved and let us finish the job without waiting on a dry line.

Gas water heaters need proper venting and combustion air. We check the flue draft, install a new vent connector, and make sure the unit has enough air for safe combustion. This is where a lot of DIY installs fail inspection.

On a closed system, thermal expansion can spike pressure and shorten tank life. We install an expansion tank sized to your system and set the pressure to match your home's water pressure.

A sediment trap catches debris before it reaches the gas valve. We install a drip leg on every gas water heater, which protects the valve and keeps the burner running clean.
We inspect the anode rod, the T&P valve, and the tank bottom. If the rod is gone and the tank shows rust, we install a new unit before it fails. If the heater still has life, we tell you and schedule a follow-up check. You avoid an emergency replacement and get a planned install on your schedule, often with a better unit choice than a panic purchase.
We calculate the new demand and recommend a 75 gallon tank or a tankless unit. We coordinate with your contractor on the gas line, venting, and drain pan so the install fits the new layout. You get enough hot water for the new tub and the rest of the house, with no cold showers after the remodel.
We stock 40 and 50 gallon gas and electric units on our trucks. If you call before noon, we can often have the new unit installed and hot water running by the end of the day. You get same-day hot water, a dry floor, and a permitted install that passes inspection.
We run a larger gas line, install PVC venting, and mount the Navien or Rheem unit on the wall. We set the temperature and show you the flush schedule. You get endless hot water, a smaller footprint, and lower standby energy loss compared to a tank.
Spring sits in Harris County, where the water is moderately hard and the summer heat pushes water heaters hard. Most homes here have a gas or electric tank in the garage or a closet. The heat and humidity in a Spring garage can shorten a heater's life, especially if the unit sits on a bare concrete floor. We install a drain pan and raise the unit on a pad to keep the bottom dry. If you are looking for a licensed water heater installer Spring TX homeowners trust, we pull the permit through the city or county and meet the inspector. We also handle tankless conversions for homes in 77373, 77383, and 77387, where gas line sizing and venting are the two biggest factors. In older neighborhoods like Old Town Spring, we often find galvanized pipes and undersized gas lines, so we quote those repairs before the install. In newer subdivisions like Harmony and Benders Landing, the install is usually a straight swap with a new expansion tank and drain pan.
A 40 gallon gas water heater in a Klein garage was leaking from the bottom and leaving a puddle. The T&P valve was stuck, the expansion tank was missing, and the shutoff valve was corroded shut.
We installed a new 50 gallon Bradford White gas heater with a new T&P valve, expansion tank, drain pan, and pan drain line. We replaced the shutoff valve and added a sediment trap. Hot water was back in three hours.
We showed the homeowner how to flush the tank every 12 months and check the anode rod at year five. The new unit is sized for their family of four.
A family of five was running out of hot water with a 50 gallon tank. They wanted endless hot water and more garage space. The existing gas line was too small for a tankless unit.
We ran a new 3/4 inch gas line, installed a Navien tankless unit on the wall, and ran PVC venting through the roof. The old tank was hauled away. The garage gained 12 square feet of floor space.
We set the temperature to 120 degrees and showed them how to flush the unit once a year with white vinegar. The flush takes about 45 minutes and keeps the heat exchanger clean.
A water heater burst on a Saturday morning and flooded the garage. The homeowner called at 9 a.m. and needed hot water before a family gathering that evening.
We arrived by 11 a.m., drained the old tank, and installed a new 50 gallon Rheem electric heater with a new drain pan and expansion tank. We pulled the permit and scheduled the inspection. Hot water was running by 2 p.m.
We checked the breaker and the wiring, then showed the homeowner where the shutoff valve is and how to reset the unit if the breaker trips. The inspection passed the following week.
If your water heater is leaking, popping, or running out of hot water, a new install solves the problem at the source. Here are the most common issues we fix.

We shut off the water and gas, drain the tank, and install a new unit with a fresh drain pan and pan drain line. We also check the shutoff valve and replace it if it is corroded. Water can ruin drywall, warp flooring, and create mold within 24 to 48 hours. A leaking tank rarely gets better and often bursts without warning.

We replace the tank and flush the lines to clear sediment. If the rust is coming from galvanized pipes, we quote a repipe or a section replacement before the new heater goes in. Rust in the water means the tank lining has failed. The heater is on borrowed time and can start leaking within weeks.

We install a new heater and add a sediment trap on gas units. We also show you how to flush the tank once a year to keep the new one running quiet. Sediment has built up on the bottom of the tank, causing hot spots and higher gas bills. The tank runs hotter, wears out faster, and can fail early.

We calculate your first-hour rating and install a larger tank or a tankless unit. A 50 gallon heater or a Navien tankless solves the problem without changing your routine. An undersized or aging heater cannot keep up with a full house. Showers turn cold, the dishwasher stalls, and mornings get stressful.
A leaking water heater can dump 40 to 60 gallons onto your floor in under an hour. We replace the tank, install a new drain pan and pan drain line, and check the T&P valve so the next failure has somewhere to go besides your drywall.
A 2026 high-efficiency gas water heater uses up to 25 percent less gas than a 15-year-old unit. If your current heater was installed before 2010, the new unit often pays back part of its cost in lower utility bills within the first few years.
A 40-gallon tank runs out fast with three showers and a dishwasher. We calculate your first-hour rating, then install a 50 gallon water heater installation Spring TX customers need for larger families, or a tankless unit if you want endless hot water.
Spring permits require proper venting, a sediment trap on gas units, an expansion tank on closed systems, and a pan with drain. We pull the permit, meet the inspector, and leave you with a sticker that shows the work passed.
Typical 2026 pricing for a standard 40 or 50 gallon tank install in Spring runs $1,200 to $2,200, including the unit, permit, fittings, drain pan, expansion tank, and haul-away. Tankless installs run $2,800 to $4,500 because they need a larger gas line and new venting. The water heater installation cost Spring TX 77379 homeowners see depends on tank size, fuel type, and whether we find corroded pipes or a bad shutoff valve. We quote a flat price before we start.
What your estimate is based on
$1,200 - $4,500 depending on tank size, fuel type, and whether it is a tank or tankless unit The price includes the unit, the permit, the fittings, the drain pan, the expansion tank, and the haul-away. You get a code-correct install that passes inspection, a manufacturer warranty, and a phone number to call if anything goes wrong.
Clear records you can keep and share.
Quoted before we drain the old tank
We pull it and meet the inspector
Loaded on our truck, not your curb
The two numbers that matter most are tank size and fuel type. Get those right and the install is straightforward. Get them wrong and you will run out of hot water or pay for a unit you do not need.
This is how much hot water the tank can deliver in one hour. It matters more than the gallon number on the label. We calculate it based on your bathrooms and appliances.
Gas units heat faster and cost less to run, but they need venting and a gas line. Electric units are cheaper to install but recover slower. We check what your home already has.
A tank stores hot water and is simpler to install. A tankless unit heats on demand and never runs out, but it needs a larger gas line and new venting. We quote both so you can compare.

Not on the list? Call and ask if we can get to you. +1 (831) 293-1204
Most standard 40 or 50 gallon tank installations in Spring run $1,200 to $2,200 in 2026, including the unit, permit, fittings, and haul-away. Tankless installs run $2,800 to $4,500 because they need a larger gas line and new venting. The water heater installation cost Spring TX 77379 homeowners see depends on tank size, fuel type, and whether we need to replace the shutoff valve or expansion tank.
A standard tank swap takes two to four hours from arrival to hot water. If we need to replace the gas line, run a new vent, or cut out corroded copper, add another hour or two. Tankless conversions take four to six hours because we run a larger gas line and new PVC venting. We schedule most jobs same-day or next morning.
For a household of one to two people, a 40 gallon tank works. Three to four people need a 50 gallon. Five or more, or a house with a large soaking tub, should go to a 75 gallon or a tankless unit. We calculate your first-hour rating based on bathrooms, appliances, and family size before recommending a size.
Yes. We drain the old tank, disconnect it, and load it on our truck at no extra charge. You do not need to schedule a bulk pickup or pay a disposal fee. We also take the old vent pipe, fittings, and packaging. If you want to keep the old unit for scrap, just tell us and we will leave it in your driveway.
We stock 40 and 50 gallon gas and electric heaters on our trucks, pull the permit, and haul away the old unit. Call now and we will give you a flat price over the phone and a same-day or next-morning install window.
Call us at +1 (831) 293-1204 or email plumbersspringtx@gmail.com. We answer calls 24/7 for emergencies. For standard service, we schedule visits Monday through Friday from 8:00 AM to 6:00 PM. If you leave a message after hours, we will call you back first thing the next morning.